工程名稱

天津港航運服務區二期啟航上東項目

工    種

 

施工部位

 

交底時間

 

交底內容

1、停放機械的地方土質要堅實平整。各機械不可超負荷使用。                                                                                                                                                                                                                                                                                                                                                                                        

2、傳動帶、電機、和齒輪必須裝有防護罩。                                                                                                                                                                                                                                                        

3、電器設備的電源線、電源接頭、電源開關、絕緣和接地必須良好。                                                                                                                                                                                                                                                                                                                                                                                  

4、各機械使用前應先空載試運轉，進行檢查、調整確認運轉正常后方可帶負荷運轉。                                                                                                                                                                                                                                                                                               

5、任何機械在使用過程中不得有漏油、超標排放廢氣、噪音等有害環境的現象。                                                                                                                                                                                                                                                                                                

6、 鋸片上方必須安裝保險擋板，傳動防護罩。機械啟動正常運轉后方可鋸料，料尾必須用木板推送。                                                                                                                             

7、 鋸料時不許將木料左右搬動或移動，送料不宜過猛。被鋸木料卡住鋸片時，應立即停車處理。被鋸木料的厚度，以不碰到固定的鋸片壓板的邊緣為限。

8、 操作中接木料時，必須待木料超過20cm以上方可接料，截?cái)嗄玖虾徒佣塘蠒r(shí)，應使用推棒不準直接用手進鋸，長度不足50cm的短料禁止上鋸。

 機械設備操作人員守則                                                                                                                                                                                               

一、服從分配，聽從指揮，保質、保量、保安全按時完成生產任務。                                                                                                                                                                                                                                                                                                                                                                                   

二、愛護設備，堅持列保，保持機械設備技術狀況良好。                                                                                                                                                                                                                                                                                                                                                                                                                                                                     

三、樹立法制觀念，認真執行設備操作規程及各項安全規章制度。                                                                                                                                                                                                                                                                                                                                                                                     

四、 遵守勞動紀律，堅守崗位。不干私活，不遲到，不早退，工作中不吸煙，不吃食物，不說笑打逗，不穿拖鞋，不讓無關人員進入駕駛室。

五、熱愛本職工作，努力學習以“四懂三會”為主要內容的技術知識，不斷提高操作   技術水平。                                                                                                                                                                                                        

在操作過程中，不按此規定者，所發生一切事故，責任自負。                                                                                                                                                                                                                                                                                                                                                                                         

 

 

 

 

 

 

 

 

 

 

 

被交底人：                  交底人：                安全員：

 

 

        年    月    日         年    月    日           年    月    日